Freeforming the denture base: Unterschied zwischen den Versionen

Aus Amann Girrbach
Wechseln zu: Navigation, Suche
 
(Eine dazwischenliegende Version desselben Benutzers wird nicht angezeigt)
Zeile 64: Zeile 64:
 
== Tab “Free” [4]==
 
== Tab “Free” [4]==
 
[[File:92.png|rand|150px|right]]
 
[[File:92.png|rand|150px|right]]
 
 
 
 
 
 
 
 
  
  
Zeile 78: Zeile 70:
 
Under the tab '''“Free” [4]''' it can be selected whether to '''“Add/Remove”''' or '''“Smooth”''' the material. The required thickness, size and type of brush can be set in the area '''“Brush” [6]'''.
 
Under the tab '''“Free” [4]''' it can be selected whether to '''“Add/Remove”''' or '''“Smooth”''' the material. The required thickness, size and type of brush can be set in the area '''“Brush” [6]'''.
  
 +
[[File:Farbliche Darstellung.jpg|rand|150px|right]]
  
  
Zeile 83: Zeile 76:
  
  
 
+
{{Tip|The thickness of the denture base can be controlled by colour
 
+
rendering. Pink areas lie below the minimum thickness and
 +
need to be strengthened by adding material.}}
  
  
Zeile 162: Zeile 156:
  
 
{{Nav|Next: [[Adapting denture base to teeth]]}}
 
{{Nav|Next: [[Adapting denture base to teeth]]}}
 +
{{Nav|Overview: [[Ceramill D-Flow (Full Denture)]]}}

Aktuelle Version vom 14. Dezember 2017, 16:00 Uhr

Fahne Deutsch.JPG




The “Freeforming” tool is available for contouring the denture base. This tool provides the possibility of processing the outer design of the denture base.


17 Mindestdickenwarnung.png

If the anatomical tooth crowns penetrate the model too deeply, then they have fallen below the minimum thickness of the base. In this case, a message appears with the following suggestions for a solution.

  • 1. Free-forming:

The Wizard remains active and the areas concerned can be strengthened

  • 2. Correction of set-up:

The Wizard closes and the procedure is as follows: _ select "Correction of tooth set-up" via the context menu and adapt the tooth set-up _ select "Design denture base" via the context menu and allow the base to be generated new again _ start Wizard and continue to follow.

WarningIf the denture is to be fabricated directly in resin, then the anatomical tooth crown should not be too over-modelled. If this cannot be avoided, the seat of the teeth in the tooth pockets of the resin bases must be checked precisely before bonding.
TipIf one wishes to fabricate the denture as a monoblock prosthesis, then it is suggested to finalise the gingiva after the try-in. Tooth repositioning may possibly make it necessary to generate the gingiva new and extensive gingiva designs would be discarded.


“Anatomical” tab [1]

91.png






Smaller “Denture Base Parts” [2], or also “Entire Denture Base” [3] can be moved under the “Anatomical” tab [1].

The respective button is activated for this and the required denture part is dragged towards where more base material is needed while keeping the left mouse key pressed.








Tab “Free” [4]

92.png



Under the tab “Free” [4] it can be selected whether to “Add/Remove” or “Smooth” the material. The required thickness, size and type of brush can be set in the area “Brush” [6].

Farbliche Darstellung.jpg



TipThe thickness of the denture base can be controlled by colour

rendering. Pink areas lie below the minimum thickness and

need to be strengthened by adding material.



Example 1: Quick alveoli modellation

1. The Gingival section of the denture base is slightly cut in using the “Parts of the denture base” tools under the “Anatomical” tab.

2. The relevant alveolus is slightly accentuated with the same tool.

3. The surface of the modellation is then smoothed using the “Smooth” tool.



Gleich.png
97.png




Example 2: Detailed papillae -alveoli modelation

1. The base surface of the alveoli is created using the “Add/Remove” tools and the brush type “Standard”.

2. The cervical papillae are created using the brush type “Cylinder” and a slightly smaller selected setting of the brush size.

3. Finally the surface of the pattern is smoothed using the “Smoothing” tool.



Gleich.png
102.png